first commit

code/SmallCart/CameraWebServer/CameraWebServer.ino

@@ -0,0 +1,114 @@
+#include "esp_camera.h"
+#include <WiFi.h>
+
+//
+// WARNING!!! Make sure that you have either selected ESP32 Wrover Module,
+//            or another board which has PSRAM enabled
+//
+
+// Select camera model
+//#define CAMERA_MODEL_WROVER_KIT
+//#define CAMERA_MODEL_ESP_EYE
+//#define CAMERA_MODEL_M5STACK_PSRAM
+//#define CAMERA_MODEL_M5STACK_WIDE
+#define CAMERA_MODEL_AI_THINKER
+
+#include "camera_pins.h"
+
+const char* ssid = "AutoWiFiManager";
+const char* password = "123456789";
+
+//静态地址、网关、子网掩码
+IPAddress local_IP(192, 168, 4, 4);
+IPAddress gateway(192, 168, 4, 1);
+IPAddress subnet(255, 255, 255, 0);
+
+void startCameraServer();
+
+void setup() {
+  Serial.begin(115200);
+  Serial.setDebugOutput(true);
+  Serial.println();
+
+  camera_config_t config;
+  config.ledc_channel = LEDC_CHANNEL_0;
+  config.ledc_timer = LEDC_TIMER_0;
+  config.pin_d0 = Y2_GPIO_NUM;
+  config.pin_d1 = Y3_GPIO_NUM;
+  config.pin_d2 = Y4_GPIO_NUM;
+  config.pin_d3 = Y5_GPIO_NUM;
+  config.pin_d4 = Y6_GPIO_NUM;
+  config.pin_d5 = Y7_GPIO_NUM;
+  config.pin_d6 = Y8_GPIO_NUM;
+  config.pin_d7 = Y9_GPIO_NUM;
+  config.pin_xclk = XCLK_GPIO_NUM;
+  config.pin_pclk = PCLK_GPIO_NUM;
+  config.pin_vsync = VSYNC_GPIO_NUM;
+  config.pin_href = HREF_GPIO_NUM;
+  config.pin_sscb_sda = SIOD_GPIO_NUM;
+  config.pin_sscb_scl = SIOC_GPIO_NUM;
+  config.pin_pwdn = PWDN_GPIO_NUM;
+  config.pin_reset = RESET_GPIO_NUM;
+  config.xclk_freq_hz = 20000000;
+  config.pixel_format = PIXFORMAT_JPEG;
+  //init with high specs to pre-allocate larger buffers
+  if (psramFound()) {
+    config.frame_size = FRAMESIZE_UXGA;
+    config.jpeg_quality = 10;
+    config.fb_count = 2;
+  } else {
+    config.frame_size = FRAMESIZE_SVGA;
+    config.jpeg_quality = 12;
+    config.fb_count = 1;
+  }
+
+#if defined(CAMERA_MODEL_ESP_EYE)
+  pinMode(13, INPUT_PULLUP);
+  pinMode(14, INPUT_PULLUP);
+#endif
+
+  // camera init
+  esp_err_t err = esp_camera_init(&config);
+  if (err != ESP_OK) {
+    Serial.printf("Camera init failed with error 0x%x", err);
+    return;
+  }
+
+  sensor_t * s = esp_camera_sensor_get();
+  //initial sensors are flipped vertically and colors are a bit saturated
+  if (s->id.PID == OV3660_PID) {
+    s->set_vflip(s, 1);//flip it back
+    s->set_brightness(s, 1);//up the blightness just a bit
+    s->set_saturation(s, -2);//lower the saturation
+  }
+  //drop down frame size for higher initial frame rate
+  s->set_framesize(s, FRAMESIZE_QVGA);
+
+#if defined(CAMERA_MODEL_M5STACK_WIDE)
+  s->set_vflip(s, 1);
+  s->set_hmirror(s, 1);
+#endif
+
+  WiFi.config(local_IP, gateway, subnet); //设置静态IP
+  WiFi.mode(WIFI_STA);
+  WiFi.begin(ssid, password);
+
+  while (WiFi.status() != WL_CONNECTED) {
+    delay(500);
+    Serial.print(".");
+  }
+  Serial.println("");
+  Serial.print("Current ip address is ");
+  Serial.println(WiFi.localIP());
+
+  startCameraServer();
+
+  Serial.print("Camera Ready! Use 'http://");
+  Serial.print(WiFi.localIP());
+  Serial.println("' to connect");
+}
+
+void loop() {
+  // put your main code here, to run repeatedly:
+  delay(10000);
+}